Festo DFM-25-100-P-A-KF Guided Cylinder | 25 mm Bore 100 mm

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DFM-25-100-P-A-KF guided cylinder. The FESTO DFM-25-100-P-A-KF is a double-acting guided drive with a 25 mm piston diameter, 100 mm stroke, and a recirculating ball bearing guide (KF) for higher load capacity and stiffness than the plain-bearing variant. It delivers 295 N theoretical advance force at 6 bar and uses P-A elastic end-position cushioning. It is used where the guided load requires precise, low-friction motion under higher side loads or moment loads — press-fit, lift, and transfer applications where the plain-bearing guide would be insufficient.
Conatct For Details
DetailReview(0)Additional

Festo DFM-25-100-P-A-KF Guided Cylinder | 25 mm Bore 100 mm

HYRIG can supply the FESTO DFM-25-100-P-A-KF guided cylinder. The FESTO DFM-25-100-P-A-KF is a double-acting guided drive with a 25 mm piston diameter, 100 mm stroke, and a recirculating ball bearing guide (KF) for higher load capacity and stiffness than the plain-bearing variant. It delivers 295 N theoretical advance force at 6 bar and uses P-A elastic end-position cushioning. It is used where the guided load requires precise, low-friction motion under higher side loads or moment loads — press-fit, lift, and transfer applications where the plain-bearing guide would be insufficient.

Key Facts



Drive typeGuided drive, DFM series
Piston diameter25 mm
Stroke100 mm
Guide typeRecirculating ball bearing guide (KF)
Theoretical force at 6 bar295 N advance / 247 N return
CushioningP-A elastic, both ends
Max. effective load at 50 mm from yoke121 N
Order code170928

Festo DFM-25 Model Specifications & Guide Variants

ModelGuide typeStrokeCushioningMax. effective loadOrder code
DFM-25-100-P-A-KFRecirculating ball bearing100 mmP-A elastic121 N170928
DFM-25-100-B-PPV-A-GFPlain-bearing100 mmPPV adjustable86 N578876
DFM-25-80-P-A-GFPlain-bearing80 mmP-A elastic86 N170927

Explore the full range in the FESTO DFM guided cylinder overview.

Data source: Technical data table.

Dimensions

ItemValue
Piston diameter25 mm
Stroke100 mm
Guide typeRecirculating ball bearing guide (KF)
Operating pressure0.15 MPa … 1 MPa (1.5 bar … 10 bar)
Max. effective load at 50 mm121 N
Max. moment Mx6.27 Nm
Max. moment My15.4 Nm
Max. moment Mz15.4 Nm
Pneumatic connectionG1/8
Operating temperature-20 °C … +80 °C

Structure / Working Principle

The DFM-25-100-P-A-KF uses the recirculating ball bearing guide (KF) instead of the plain-bearing guide. The guide rods run on recirculating balls, which reduces friction and provides higher stiffness and load capacity. The trade-off is higher cost and greater sensitivity to contamination — the ball guide requires clean, dry air and a clean working environment, and it is not suitable for applications where abrasive dust or metal particles can enter the bearing.

The P-A elastic cushioning absorbs the end-of-stroke impact without an adjustment screw. Compared with the PPV adjustable cushioning on the GF variant, the P-A cushioning is simpler to commission but cannot be tuned to different loads or speeds. The max. effective load at 50 mm from the yoke is 121 N for the KF variant, higher than the 86 N for the GF variant — this reflects the higher stiffness of the ball bearing guide.

Cross-Reference & Replacement

Replacing a plain-bearing DFM or a competitor guided cylinder with the DFM-25-100-P-A-KF? Check these four points:

  1. Bore and stroke: 25 mm / 100 mm — match the existing motion envelope.
  2. Guide type: KF (recirculating ball bearing) provides higher stiffness and load capacity than GF (plain-bearing). If the existing application uses a GF guide and the side load is moderate, the KF is an upgrade; if the environment is dusty, confirm that the ball guide is suitable.
  3. Cushioning: P-A elastic (no adjustment) vs PPV adjustable. If the existing application relies on tuned cushioning, the P-A variant may change the deceleration profile.
  4. Max. effective load: 121 N at 50 mm from the yoke for the KF variant. Confirm that the existing load and lever arm are within this limit.

For a broader replacement checklist, see the FESTO guided cylinder replacement guide.

Applications

  • Press-fit stations with higher side loads: where the ball bearing guide absorbs the lateral reaction forces and the higher stiffness keeps the press tool aligned.
  • Lift and lower motions with moment loads: where the load centre is offset and the guide must resist tilting moments, with the KF guide providing higher Mx and My/Mz capacity.
  • Transfer slides requiring low friction: where the recirculating ball guide reduces stick-slip and provides smooth motion at low speeds.
  • Clean-room or clean-environment applications: where the ball guide can operate within its contamination limits and the higher stiffness is required.

Selection Support

Not sure whether the KF ball bearing guide is necessary for your side load and moment, or need the GF plain-bearing variant for a dusty environment? Send your load, side-load direction, moment arm, contamination level, and cushioning requirement, and we will confirm the guide type and accessory combination.

Frequently Asked Questions

Q: What is the theoretical force of the Festo DFM-25-100-P-A-KF at 6 bar?
A: 295 N advance and 247 N return, based on the 25 mm piston area.

Q: What is the difference between KF and GF guides on the DFM series?
A: KF is a recirculating ball bearing guide, with higher stiffness and load capacity (121 N max. effective load at 50 mm). GF is a plain-bearing guide, with lower friction but lower load capacity (86 N) and better tolerance for contamination.

Q: Does the DFM-25-100-P-A-KF have adjustable cushioning?
A: No. The P-A suffix indicates elastic end-position cushioning without an adjustment screw. If adjustable cushioning is required, choose a PPV-A variant.

Q: What is the maximum effective load at 50 mm from the yoke?
A: 121 N, based on the recirculating ball bearing guide capacity.

Q: What is the lead time for Festo DFM-25-100-P-A-KF?
A: Standard lead time is 7–17 days from order confirmation, based on the quoted supply status.

Contact

For FESTO DFM-25-100-P-A-KF selection and yoke plate accessories, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit