HYRIG can supply the FESTO SME-8-K-LED-24 proximity sensor. The FESTO SME-8-K-LED-24 is a reed-type proximity sensor for T-slot cylinders, with a normally-open (N/O) contact output, a 12–30 VDC operating voltage range, and a 2.5 m cable. It is used to detect the piston position in T-slot cylinders where a simple contact closure is preferred over a PNP/NPN solid-state output, and the 2.5 m cable allows direct connection to a terminal box without an intermediate connector.
| Sensor type | Reed proximity sensor |
| Mounting | T-slot |
| Output function | Normally open (N/O) contact |
| Operating voltage | 12 VDC … 30 VDC |
| Electrical connection | 2.5 m cable |
| Protection class | IP65 / IP67 |
| Weight | 30 g |
| Order code | 150855 |
| Model | Output | Connection | Cable length | Order code |
|---|---|---|---|---|
| SME-8-K-LED-24 | N/O contact | Cable | 2.5 m | 150855 |
| SME-8-K-LED-24 | N/O contact | Cable | 2.5 m | 150855 |
| SME-8M-DS-24V-K-2,5-OE | N/O contact | Cable | 2.5 m | — |
Explore the full range in the FESTO SME-8 proximity sensor overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Mounting type | T-slot, insertable into the slot |
| Electrical connection | 2.5 m cable |
| Operating voltage | 12 VDC … 30 VDC |
| Output function | Normally open contact |
| Protection class | IP65 / IP67 |
| Weight | 30 g |
| Operating temperature | -40 °C … +85 °C |
The SME-8-K-LED-24 is a reed-type sensor that uses a glass-encapsulated reed switch actuated by the magnetic field of the piston magnet. When the piston magnet approaches the sensor, the reed contacts close, completing the circuit. The LED indicator shows the switching status, which helps during commissioning and troubleshooting.
The 2.5 m cable is long enough to reach a terminal box or a PLC input module without an intermediate connector, reducing installation time and potential failure points. The IP65/IP67 protection class covers dust and water jets, making the sensor suitable for machine-tool and washdown-adjacent environments. Unlike a magnetoresistive sensor, the reed sensor has no active electronics in the sensing head, so it is tolerant of electrical noise — but the contact life is finite, and the switching frequency is lower than a solid-state sensor.
Not sure whether a reed contact or a solid-state PNP/NPN sensor matches your PLC input, or need a longer cable for a different installation layout? Send your PLC input type, cable length requirement, switching frequency, and cylinder model, and we will confirm the sensor output and connection.
Q: What is the output type of the Festo SME-8-K-LED-24?
A: Normally open (N/O) contact, with a 12–30 VDC operating voltage range.
Q: What is the cable length of the SME-8-K-LED-24?
A: 2.5 m, which allows direct connection to a terminal box without an intermediate connector.
Q: What is the difference between SME-8 and SMT-8M?
A: SME-8 is a reed-type sensor with a contact output; SMT-8M is a magnetoresistive sensor with a solid-state PNP or NPN output. The SME-8 has no active electronics in the sensing head and is tolerant of electrical noise, but the contact life is finite.
Q: What is the protection class of the SME-8-K-LED-24?
A: IP65 / IP67, covering dust and water jets for machine-tool and washdown-adjacent environments.
Q: What is the lead time for Festo SME-8-K-LED-24?
A: The base model is discontinued. Confirm availability with HYRIG before ordering; alternative reed sensors may be available.
For FESTO SME-8-K-LED-24 selection and alternative sensor options, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.