Welcome to Hyrig – your trusted supplier for replacement Shenkai FZ35-70G, FZ35-105G and 2FZ35-105G ram blowout preventers (BOP) and all spare parts.
In Shenkai's nomenclature system, G indicates the improvement sequence number (改进序例号), representing a specific generation of engineering refinement. The sequence E, F, G… corresponds to increasingly improved iterations, with G‑Type representing a more advanced version compared to previous models.
This is not a structural designation (such as S‑Type, U‑Type, D‑Type) but rather a developmental generation code that encompasses:
Enhanced sealing structure configurations
Optimized hydraulic cylinder and piston designs
Improved side door seal systems for high‑pressure gas‑tight integrity
Refined overall reliability for extreme HPHT operation
The FZ**G series are thus improved models that retain full compatibility with original equipment while delivering incremental but important engineering advances.
The G design sequence is part of Shenkai's full model naming system, where each alphanumeric character conveys specific information.
All G‑Type models satisfy the Shenkai ultra‑high pressure engineering baseline:
Forged alloy steel construction – pressure‑containing components are forged, delivering superior strength, impact toughness, and structural integrity
Side door combined seal – uses high‑pressure combined seal ring for anti‑H₂S gas tightness
Piston double‑seal design – improving sealing reliability in 105MPa extreme conditions
Wedge‑block hydraulic lock – closing and locking share same circuit; unlocking and opening share same circuit; booster cylinder in unlocking chamber greatly improves unlocking capability
Large‑diameter cylinder – improves the closing ratio, providing enhanced shearing capacity
Shear ram engineering – shear life in more than five times; replaceable sealing rubber
Internal H2S resistance – all well fluid contact surfaces resistant to sulfide stress corrosion, complying with NACE MR0175 requirements
| Model | Bore (mm/in) | Working Pressure (MPa/psi) | Test Pressure (MPa/psi) | Configuration | Application |
|---|---|---|---|---|---|
| FZ35-70G | 346.1 / 13-5/8" | 70 MPa / 10,000 psi | 105 MPa / 15,000 psi | Single ram | 13-5/8" HPHT deep wells |
| FZ35-105G | 346.1 / 13-5/8" | 105 MPa / 15,000 psi | 158 MPa / 22,500 psi | Single ram | Ultra‑deep well primary barrier |
| 2FZ35-105G | 346.1 / 13-5/8" | 105 MPa / 15,000 psi | 158 MPa / 22,500 psi | Double ram | Dual‑chamber emergency control |
Nominal bore: 346.1 mm (13-5/8 inches)
Working pressure: 70 MPa (10,000 psi)
Strength test pressure: 105 MPa (15,000 psi)
Hydraulic control pressure: 21 MPa (3,000 psi rated)
Recommended hydraulic operating pressure: 8.4 – 10.5 MPa (1,200 – 1,500 psi)
Ram types supported: Pipe ram, blind ram, shear ram, variable bore ram
Flange connection: 13-5/8" API 6B/6BX
Temperature class: Metal: -29°C to +121°C; Non‑metal: -18°C to +121°C
H₂S resistance: NACE MR0175 compliant, anti‑sulfide stress cracking
Shear capability: at 21 MPa hydraulic closing pressure, can shear 5", G-105 grade drill pipe (multi‑cycle capability)
Compliance: API Spec 16A, GB/T 20174
Nominal bore: 346.1 mm (13-5/8 inches)
Working pressure: 105 MPa (15,000 psi)
Strength test pressure: 158 MPa (22,500 psi)
Hydraulic control pressure: 21 MPa (3,000 psi rated)
Close oil volume (single cylinder): 42 L
Open oil volume (single cylinder): 37 L
Weight: approx. 8,260 kg (18,360 lb)
Flange connection: 13-5/8" API 6BX (BX‑type ring gasket)
Temperature class: Metal T20 (-29°C to +121°C); Non‑metal BGB (-18°C to +93°C)
Wedge‑block hydraulic lock: Standard
Shear ram: shear life more than five times; dedicated design for 5" drill pipe
NACE MR0175: complete anti‑H₂S sour service compliance
Compliance: API Spec 16A
Nominal bore: 346.1 mm (13-5/8 inches)
Working pressure: 105 MPa (15,000 psi)
Strength test pressure: 158 MPa (22,500 psi)
Hydraulic control pressure: 21 MPa (3,000 psi rated)
Weight: approx. 14,930 kg (33,180 lb)
Two independent ram chambers in a single forged body
Ram combinations supported: pipe+blind, pipe+shear, blind+shear, or dual‑sized pipe rams
Forged alloy steel construction – all pressurised parts forged
Straight‑line side door movement – each side door controlled by two dedicated hydraulic cylinders
Automatic sand‑cleaning structure – built into the shell to prevent debris build‑up
Auto‑locking wedge mechanism – closing and locking same circuit; unlocking and opening same circuit
Secondary seal on middle flange – emergency grease injection capability
NACE MR0175 – all well‑contacted surfaces H₂S resistant
The G‑Type improves upon earlier "E" and "F" generations through:
Refined sealing groove geometry for high‑pressure gas service
Optimized side door seal retention profiles
Enhanced hydraulic passages for more predictable closing response
Updated shear ram kinematics – designed for both shear performance and reuse
Improved NACE MR0175 coating coverage for sour gas environments
Parts are identical in form, fit and function to original Shenkai G‑Type equipment.
Quantities listed are for single ram BOPs; double ram models require double the quantity for ram‑related parts.
Ram rubber (packing element) – high‑pressure anti‑H₂S compound for 70MPa or 105MPa rating; specify pipe size
Front seal – per ram (1 set per single ram BOP; 2 sets for double ram)
Top seal – per ram (1 set per BOP; 2 sets for double ram)
Side door combined seal ring – high‑pressure gas‑tight ring (one per side door)
Complete seal kit (repair kit) – all O‑rings, Y‑rings, wipers, dynamic seals for full overhaul
Piston rod seal – Y‑ring dynamic seal for hydraulic cylinder
Wiper ring / dust‑proof ring
Pipe ram assembly – complete assembly with ram rubber; specify pipe OD (2-3/8" through to 10-3/4")
Blind ram assembly – full wellbore closure
Shear ram assembly – shear life more than five times with replaceable sealing rubber; can shear 5" G-105 drill pipe
Variable bore ram (VBR) – seals multiple pipe diameters without ram change
Ram body without rubber – for field rubber replacement
Ram shaft assembly – complete with Y‑ring seals
Piston rod – heavy‑duty chrome‑plated
Piston – double‑seal configuration
Hydraulic cylinder body – integral to side door (forged alloy steel)
Cylinder head – bolted to side door
Locking screw assembly – manual lock shaft, nut, handle (standard)
Leadscrew assembly – manual lock component
Wedge‑block hydraulic lock assembly – for 105MPa variants
BOP main body – single ram or double ram configuration, forged alloy steel
Side doors (left/right) – straight‑line hydraulic movement (double ram) or hinged (single ram)
Flanged connections – top and bottom, API 6B/6BX
Ring gaskets – BX or R type per API 6BX
Stud bolts and heavy hex nuts – Grade B7 or equivalent, NACE MR0175 for sour service
Secondary seal assembly – middle flange emergency grease injection system
Automatic sand‑cleaning structure – for double ram body
Lifting eyes / lugs – heavy‑duty four‑point lifting
Nameplate – stainless steel with serial number and rating
All parts are high‑quality replacement – 100% interchangeable with original Shenkai G‑Type components.
Stock ready – common wear parts for FZ35-70G, FZ35-105G and 2FZ35-105G ship within 3‑7 days
Technical support – drawing verification before ordering; ram configuration and G‑Type compatibility assistance
International shipping – by air or sea to any oilfield, HPHT project
API compliance – manufactured to API Spec 16A
Full sour service capability – NACE MR0175 compliance for H₂S fields
G‑Type engineering knowledge – correct replacement parts for improved generation BOPs
13-5/8" HPHT deep well primary BOP for onshore drilling
Offshore platform large‑bore well control
High‑pressure deep well completion operations
Primary well barrier in F35-105 HPHT BOP stacks
Ultra‑deep well drilling (9,000 m+ depth)
High‑pressure sour gas well operations with NACE MR0175
Deepwater HPHT exploration drilling
Dual‑chamber emergency well control for ultra‑deep HPHT wells
Core component of F35-105 BOP stack – provides redundant barrier in single housing
Pipe+shear ram configuration for both sealing and emergency cutting
The G‑Type improved models are particularly suitable for critical environments where incremental reliability improvements matter, including H₂S‑prone formations and gas‑producing zones requiring high gas‑tight integrity.
Send your inquiry with:
Model number (FZ35-70G, FZ35-105G, or 2FZ35-105G)
Ram types and pipe sizes for each chamber
Sour service requirement (Yes/No – NACE MR0175)
Low‑temperature requirement (Yes/No)
Original part number (if available)
We will reply with a quote and technical drawing if needed.
For any inquiries, please contact us at info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.