Torque Reduction Sub – TVR207 – Complete Product Introduction

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Torque reduction sub is designed to reduce excessive torque generated when drilling in short radius horizontal sections and high angle well sections. It is mainly connected between these challenging intervals. It is proposed to connect one torque reduction sub approximately every 60 feet (18.3 m). After using this tool, torque can be reduced by 25‑35%. The tool features a slip spiral inner sleeve, a straight rib outer sleeve, and a body mandrel that are relatively in a non‑rotating condition. Model TVR207 has a working OD of 207.2 mm (8‑5/32″), a tool OD of 174.5 mm (6‑7/8″), an ID of 108 mm (4‑1/4″), an overall length of 1194 mm (3.9 ft), and an XT57 B×P connection.

Conatct For Details
DetailReview(0)Additional

Overview
The torque reduction sub is a specialized downhole tool designed to reduce the excessive torque generated when drilling in short radius horizontal sections and high angle (deviated) well sections. These well profiles typically create high frictional drag between the drill string and the borehole wall, leading to increased surface torque, reduced weight transfer, and potential stuck pipe. The torque reduction sub is mainly connected between short radius horizontal sections and high angle sections. It is recommended to connect one torque reduction sub approximately every 60 feet (18.3 m) along the drill string. Field experience shows that using this tool can reduce torque by 25‑35%. The unique design features a slip spiral inner sleeve, a straight rib outer sleeve, and a body mandrel that are relatively in a non‑rotating condition, which decouples the outer sleeve from the rotating string and significantly lowers frictional resistance.

Key Features

  • Significant Torque Reduction – Reduces drilling torque by 25‑35% in high‑drag sections.

  • Short Radius & High Angle Optimized – Specifically designed for challenging well profiles where conventional drill pipe experiences high friction.

  • Non‑Rotating Sleeve Design – Slip spiral inner sleeve and straight rib outer sleeve remain relatively non‑rotating relative to the borehole wall.

  • Recommended Spacing – Install one sub every 60 ft (18.3 m) for optimal performance.

  • Improved Weight Transfer – Lower torque allows higher weight on bit (WOB) and better slide drilling efficiency.

  • Single Model TVR207 – Suitable for medium to large hole sizes.

Working Principle
The torque reduction sub consists of three main components: a body mandrel (which rotates with the drill string), a slip spiral inner sleeve, and a straight rib outer sleeve. The inner sleeve and outer sleeve are designed to rotate at a different rate (or not rotate) relative to the mandrel, typically using bearings or low‑friction interfaces. When the drill string rotates, the mandrel turns, but the outer sleeve remains substantially stationary against the borehole wall. This eliminates the sliding friction that would otherwise occur between a rotating pipe and the formation or casing. The spiral ribs on the inner sleeve and straight ribs on the outer sleeve also help centralize the tool and allow cuttings to pass. Because the outer sleeve does not rotate, torque generated from wall contact is drastically reduced. By placing these subs at intervals (e.g., every 60 ft), the cumulative frictional torque along the entire horizontal or high‑angle section is lowered by 25‑35%, allowing smoother drilling, lower surface power requirements, and reduced wear on the drill string.

Technical Specifications (Model TVR207)

ParameterSpecification
ModelTVR207
Working OD mm (inch)207.2 (8-5/32)
Tool OD (Fishing OD) mm (inch)174.5 (6-7/8)
ID mm (inch)108 (4-1/4)
Overall Length mm (ft)1194 (3.9)
ConnectionXT57 B×P

Note: Other sizes and custom specifications are available upon request – refer to the technical agreement for details.

Applications

  • Short radius horizontal wells (build rates >30°/100 ft)

  • High angle and extended reach wells (deviations >60°)

  • Sections where torque and drag limit drilling progress or prevent reaching total depth

  • Onshore and offshore drilling, including deepwater and ultra‑extended‑reach wells

  • Placed between drill pipe joints in the curved or lateral section, one sub every 60 ft (18.3 m)

Value Proposition

  • 25‑35% Torque Reduction – Proven field results extend reach and reduce surface power requirements.

  • Smoother Slide Drilling – Lower friction improves weight transfer, reducing slide‑drilling time.

  • Reduces Stuck Pipe Risk – Less drag and torque lower the chance of differential sticking or mechanical pack‑off.

  • Extends Equipment Life – Reduces wear on top drive, rotary table, and drill pipe tool joints.

  • Simple Integration – Installed like a standard drill pipe sub; no special tools or modifications required.

The TVR207 torque reduction sub is a proven solution for reducing excessive torque in short radius horizontal and high angle wells. By placing these subs every 60 feet, operators can lower torque by 25‑35%, improve drilling efficiency, and reach deeper targets that would otherwise be unattainable due to friction limits.

Contact Us
For technical data sheets, placement recommendations, or a quotation, please contact:
Email: info@hyrig.com


Torque Reduction Sub – Reduce torque by 25‑35%, extend your reach.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit