Hydraulic Variable Gauge Stabilizer – WLB216 – Complete Product Introduction

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Hydraulic variable gauge stabilizer is used in directional well drilling. It uses an extendable hardfacing block to reach full hole size, ensuring that the stabilizer can achieve slope increasing or slope stabilizing when working with different drilling tool combinations in directional wells. When the pump is stopped, the hardfacing block retracts, and the outer diameter becomes small – which is beneficial for smooth drilling and tripping, and effectively prevents resistance and stuck pipe. Model WLB216 features a variable diameter range of 196.9 mm to 215.9 mm (7‑3/4″ to 8‑1/2″), an inner diameter of 38.1 mm (1‑1/2″), overall length 3038 mm (10 ft), and an NC50 B×P connection.

Conatct For Details
DetailReview(0)Additional

Overview
The hydraulic variable gauge stabilizer is a specialized downhole tool designed for directional well drilling. It uses a hydraulically actuated, extendable hardfacing block that expands to reach full hole size. This unique feature allows the stabilizer to achieve two critical directional functions – slope increasing (building angle) and slope stabilizing (holding angle) – when used with different bottom hole assembly (BHA) combinations in directional drilling. When the mud pump is stopped, the hardfacing block retracts, reducing the tool’s outer diameter. This smaller diameter facilitates smooth drilling and tripping operations and effectively prevents resistance, drag, and stuck pipe.

Key Features

  • Hydraulic Expansion – Hardfacing block extends when pump pressure is applied, reaching full gauge diameter.

  • Slope Increasing & Stabilizing – With different BHA configurations, the tool can either build angle or hold angle.

  • Retractable Design – When pumps stop, the block retracts, reducing OD for easy tripping.

  • Prevents Resistance & Stuck Pipe – Small retracted OD eliminates hang‑ups during tripping.

  • Hardfaced Block – Wear‑resistant hardfacing on the extending block ensures long service life in abrasive formations.

  • Single Model WLB216 – Variable diameter range 196.9–215.9 mm (7‑3/4″ – 8‑1/2″), suitable for 8‑1/2″ hole sections.

Working Principle
The WLB216 hydraulic variable gauge stabilizer is placed in the BHA at a strategic position (typically near the bit or between drill collars). Under normal circulation (pump on), drilling fluid pressure acts on a piston inside the tool, forcing the hardfacing block outward until it contacts the borehole wall. The block locks at full gauge diameter (215.9 mm / 8‑1/2″), providing a full‑size stabilizer contact point. Depending on the BHA configuration (e.g., with a bent housing motor or with straight collars), this full‑gauge contact can either increase the build rate (slope increasing) or maintain the current angle (slope stabilizing).

When the pump is stopped (e.g., to make a connection or to trip out), hydraulic pressure is lost. A return spring or differential pressure retracts the hardfacing block back into the tool body. The tool’s outer diameter reduces to its minimum (196.9 mm / 7‑3/4″), which is significantly smaller than the hole size. This reduced OD allows the BHA to be pulled through tight spots, ledges, or doglegs without hanging up, preventing stuck pipe and reducing tripping time.

Technical Specifications (Model WLB216)

ParameterSpecification
ModelWLB216
Variable Diameter Range mm (inch)196.9 (7-3/4) ~ 215.9 (8-1/2)
ID mm (inch)38.1 (1-1/2)
Overall Length mm (ft)3038 (10.0)
ConnectionNC50 B×P

Note: Other sizes and custom specifications are available upon request – refer to the technical agreement for details.

Applications

  • Directional well drilling (build sections, tangent sections, and drop sections)

  • Horizontal well drilling where variable stabilization is needed for trajectory control

  • Wells where tripping resistance is a concern (tight holes, doglegs, ledges)

  • Onshore and offshore drilling with mud motor or rotary BHA configurations

  • 8‑1/2″ hole sections (common for intermediate and production holes)

Value Proposition

  • Dual Function – One tool provides both slope increasing and slope stabilizing, reducing the number of BHA changes.

  • Prevents Stuck Pipe – Retractable OD ensures smooth tripping through tight spots, significantly reducing non‑productive time.

  • No Additional Surface Equipment – Hydraulic actuation uses existing mud pumps; no electric or hydraulic lines.

  • Robust Hardfacing – Extended block life in abrasive formations.

  • Simple & Reliable – Few moving parts, easy to maintain.

The WLB216 hydraulic variable gauge stabilizer is a powerful tool for directional drillers who need to control well trajectory while minimizing tripping risks. By expanding to full gauge under pump pressure, it provides effective stabilization for building or holding angle. When the pump stops, it retracts to a smaller diameter, allowing the BHA to move freely – preventing resistance, drag, and stuck pipe.

Contact Us
For technical data sheets, BHA configuration recommendations, or a quotation, please contact:
Email: info@hyrig.com


Hydraulic Variable Gauge Stabilizer – Expand to control trajectory, retract to trip safely.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit