Overview
The non‑rotating stabilizer is a specialized drilling tool used in oil drilling processes. Its main function is the same as that of a normal stabilizer – to center the bottom hole assembly (BHA), control well deviation, reduce vibration, and improve drilling performance. However, the non‑rotating stabilizer offers an additional critical advantage: it significantly reduces torque resistance. This is achieved through its unique two‑piece construction consisting of a mandrel (which rotates with the drill string) and a sleeve (which is designed to remain stationary or rotate at a much lower speed relative to the borehole wall or casing). By minimizing rotational friction, the tool reduces torque on the drill string, protects casing, and lowers surface power requirements. When the sleeve becomes worn due to abrasion, it can be easily replaced, allowing the mandrel to be reused – reducing operating costs.
Key Features
Torque Reduction – Sleeve remains non‑rotating or slips relative to the borehole, dramatically reducing frictional torque.
Same Stabilization Function – Provides full centralization and deviation control like a conventional stabilizer.
Two‑Piece Construction – Mandrel (rotating) and sleeve (non‑rotating or low‑friction).
Replaceable Sleeve – Worn sleeves can be changed out, extending tool life and lowering cost.
Casing Protection – Non‑rotating sleeve reduces wear on casing strings when drilling through cased sections.
Wide Size Range – Models from 146 mm (5‑3/4″) to 711 mm (28″) working OD.
Working Principle
The non‑rotating stabilizer is placed in the BHA as a string stabilizer. The mandrel is connected to the drill string and rotates with it. The sleeve is mounted on the mandrel via a bearing or friction‑reducing interface (e.g., rubber sleeve, roller bearings, or low‑friction material). When the drill string rotates, the mandrel spins inside the sleeve, while the sleeve remains substantially stationary against the borehole wall or casing. This decoupling of rotation from the stabilizer body eliminates the sliding friction that would otherwise occur between a conventional rotating stabilizer and the formation or casing. As a result, torque and drag are significantly reduced, allowing longer lateral sections, higher rotational speeds, and reduced wear on casing. The sleeve’s blades still contact the wall to centralize the BHA, but without generating high frictional torque. When the sleeve blades wear down, the tool is pulled out, the worn sleeve is removed, and a new sleeve is installed – the mandrel is reused.
Technical Specifications
| Model | Blade OD mm (inch) | ID mm (inch) | Body OD mm (inch) | Blade Length mm (inch) | Connection |
|---|---|---|---|---|---|
| FX146 | 146 (5-3/4) | 50.8 (2) | 120.7 (4-3/4) | 180 (7-5/64) | NC38 |
| FX197 | 197 (7-3/4) | 57.2 (2-1/4) | 165 (6-1/2) | 203 (8) | NC50 |
| FX210 | 210 (8-17/64) | 57.2 (2-1/4) | 165 (6-1/2) | 203 (8) | NC50 |
| FX240 | 240 (9-29/64) | 57.2 (2-1/4) | 165 (6-1/2) | 203 (8) | NC50 |
| FX311 | 311.15 (12-1/4) | 71.4 (2-13/16) | 209.6 (8-1/4) | 356 (14-1/14) | 6-5/8 REG |
| FX406 | 406 (16) | 76.2 (3) | 241.3 (9-1/2) | 464 (18-17/64) | 7-5/8 REG |
| FX432 | 432 (17) | 76.2 (3) | 241.3 (9-1/2) | 500 (19-11/16) | 7-5/8 REG |
| FX559 | 558.8 (22) | 76.2 (3) | 241.3 (9-1/2) | 610 (24) | 7-5/8 REG |
| FX711 | 711 (28) | 76.2 (3) | 241.3 (9-1/2) | 710 (28) | 7-5/8 REG |
Note: Custom specifications and other sizes are available upon request – refer to the technical agreement for details.
Applications
Directional, horizontal, and extended‑reach wells where torque and drag are limiting factors
Drilling through casing or liner sections where protecting the casing from wear is critical
Long lateral sections where conventional rotating stabilizers would generate excessive torque
Onshore and offshore drilling, including deepwater and ultra‑extended‑reach wells
Replacing conventional stabilizers in BHA designs to reduce surface torque and improve weight transfer
Value Proposition
Reduced Torque & Drag – Non‑rotating sleeve eliminates frictional resistance, allowing longer laterals and higher ROP.
Casing Protection – Minimizes wear on intermediate and production casing strings.
Lower Surface Power Requirements – Less torque means lower hydraulic and mechanical loads on top drive.
Replaceable Sleeve – Extends tool life; only the sleeve needs replacement, reducing capital expenditure.
Same Stabilization Performance – Provides full well deviation control and BHA centralization.
Wide Range of Sizes – Models from 5‑3/4″ to 28″ OD to fit almost any hole section.
The FX series non‑rotating stabilizer delivers the same reliable well deviation control as a conventional stabilizer but with the critical added benefit of torque reduction. By allowing the sleeve to remain stationary against the borehole wall, it minimizes frictional torque, protects casing, and enables longer, more challenging drilling intervals. The replaceable sleeve design further reduces operating costs.
Contact Us
For technical data sheets, sleeve replacement intervals, or a quotation, please contact:
Email: info@hyrig.com
Non‑Rotating Stabilizer – Stabilize the well, reduce the torque, protect the casing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.