Overview
The JZ shock absorber is a dedicated vertical shock absorbing tool specifically designed for drilling operations using cone bits (roller cone bits) or abrasive coring bits. These bit types are particularly susceptible to vertical impact loads (bit bounce) when drilling through hard, interbedded, or fractured formations. The JZ shock absorber effectively absorbs or slows down vertical shock and impact loads transmitted through the drill stem during drilling. By mitigating these destructive forces, the tool maintains normal drilling pressure, prolongs the service life of the drill bit, protects both downhole drilling tools and surface equipment, decreases overall drilling cost, and increases drilling efficiency.
Key Features
Vertical Shock Absorption – Specifically targets axial (vertical) impacts, the primary cause of bit tooth and bearing damage in roller cone bits and core bits.
Maintains Normal Drilling Pressure – Smooths out weight on bit (WOB) fluctuations, allowing the driller to maintain optimal drilling parameters.
Prolongs Bit Life – Reduces impact damage to bit teeth, carbide inserts, and bearing seals – typically extending bit life by 30‑50%.
Protects Drill Stem & Surface Equipment – Minimizes fatigue and impact damage to drill pipe, tool joints, top drive, and rotary table.
Cost Reduction & Efficiency Gain – Fewer bit trips, less equipment damage, and more consistent ROP directly lower cost per foot.
Wide Operating Temperature – Rated from -40°C to 150°C, suitable for most drilling environments including arctic and deep wells.
Working Principle
The JZ shock absorber contains a compressible hydraulic fluid or spring‑assisted hydraulic damping mechanism within a sealed piston‑cylinder arrangement. When the drill bit encounters a hard streak or formation change, upward axial forces compress the piston into the damping chamber. The internal fluid (or combination of fluid and mechanical elements) resists rapid compression, converting the kinetic energy of the impact into heat. This controlled resistance slows the upward velocity of the drill stem, dramatically reducing the peak impact load transmitted to the bit, BHA, and surface equipment. After the impact, the damping mechanism returns the piston to its neutral position, ready for the next cycle. The result is a smoother, more constant WOB and significantly reduced shock loading on bit teeth and bearings.
Technical Specifications (Model JZ178)
| Parameter | Specification |
|---|---|
| Model | JZ178 |
| OD mm (inch) | 178 (7) |
| ID mm (inch) | 57.2 (2-1/4) |
| Working Temperature | -40°C ~ 150°C |
| Max Stroke mm (inch) | 120 (4-3/4) |
| Max Working Torque (Limited) KNm (lbf·ft) | 15 (11,000) |
| Max Tensile Load KN (lbf) | 1500 (337,000) |
| Overall Length mm (ft) | 2570 (8.4) |
| Connection (API) | NC50 |
Note: Other sizes and custom specifications are available upon request – refer to the technical agreement for details.
Applications
Drilling with roller cone bits (all types: milled tooth, tungsten carbide insert, sealed bearing, air bearing)
Abrasive coring operations where core bit life is limited by impact damage
Hard rock drilling (granite, basalt, chert, quartzite)
Interbedded formations with abrupt hardness contrasts
Wells where bit bounce is causing low ROP, premature bit failure, or BHA damage
The JZ shock absorber is especially valuable in applications where maintaining consistent WOB is difficult due to severe vertical vibrations, and where bit trips are frequent due to impact‑related tooth or bearing failure.
Value Proposition
Longer Bit Runs – Protects teeth/inserts and bearings, allowing the bit to drill its full footage potential.
Reduced Non‑Productive Time – Fewer trips for bit changes means more time drilling.
Lower Bit Cost per Foot – Extended bit life directly reduces drilling cost.
Protects Expensive BHA Components – Reduces shock to MWD/LWD tools, mud motors, and rotary steerable systems.
Decreased Surface Equipment Maintenance – Less vibration transmitted to top drive, swivel, and drawworks.
Proven Reliability – Simple, rugged design with wide temperature tolerance.
The JZ shock absorber is a straightforward, effective, and economical solution for mitigating vertical shock in cone bit and coring bit drilling. By absorbing impact before it damages the bit and drill stem, it helps operators drill faster, cheaper, and with fewer interruptions.
Contact Us
For technical data sheets, custom sizing inquiries, or a quotation, please contact:
Email: info@hyrig.com
JZ – Smooth vertical shock, extend bit life, lower drilling cost.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.