Welcome to Hyrig – your trusted supplier for replacement Shenkai FZ68-35 ultra-large bore ram blowout preventers (BOP) and all spare parts. The FZ68-35 comes with a nominal bore of 26-3/4 inches (679mm) and a 35MPa (5,000 psi) working pressure rating. It is designed for surface well control in conductor casing programs.
The model number FZ68-35 follows the Chinese industry standard:
FZ – Ram blowout preventer
68 – Nominal bore: approx. 680mm (26-3/4 inches) ─ the number indicates bore size in centimeters (68cm)
35 – Maximum working pressure: 35MPa (5,000 psi)
The same naming system applies to the entire product family: FZ35-70 is 13-5/8″ 70MPa (10,000 psi) while FZ68-35 is 26-3/4″ 35MPa (5,000 psi). They cover industry standard bore sizes from 7-1/16″ through to 30″.
Model: FZ68-35 (single ram configuration)
Nominal bore: 679 mm (26-3/4 inches)
Working pressure: 35 MPa (5,000 psi)
Strength test pressure: 52.5 MPa (7,500 psi)
Hydraulic control pressure: ≤10.5 MPa (1,500 psi)
Application: Surface well control at conductor casing depths
Flange connection: API 6B, 26-3/4″ 5,000 psi top and bottom
Working medium: Oil, water, drilling fluid
Compliance: API Spec 16A
This BOP is sized to match 26-3/4″ wellhead flanges in surface well control stacks.
Ram rubber (packing element) – for 26-3/4″ bore; specify pipe size (typically 13-3/8″ or 16″ casing range)
Front seal – per ram for FZ68-35 front ram block sealing
Top seal – ram top rubber seal to close against housing
Side door seal – high-pressure combined seal rings for 26-3/4″ BOP
Complete seal kit (repair kit) – all O-rings, Y-rings, wipers, guide rings for full overhaul
Piston rod seals (Y-ring) – dynamic sealing for hydraulic cylinder
Wiper rings / dust-proof rings
Ram block assembly (complete with rubber) – with 13-3/8″ or 16″ pipe size capabilities
Ram body – without rubber, for field replacement
Ram shaft assembly – ram shaft and Y-seal ring assembly
Piston rod – chrome-plated, wear-resistant
Piston – for hydraulic cylinder
Hydraulic cylinder body
Cylinder head
Locking screw assembly – manual lock shaft, nut, handle
Leadscrew assembly
Stud bolts – for flanges and side door connections, Grade B7 or equivalent
Heavy hex nuts – NACE MR0175 on request
Ring gaskets – API 6B R-type or BX-type depending on stack requirements
Socket head cap screws, guide pins, retaining rings
BOP main body – single ram housing, forged or cast alloy steel
Flanged connections – top and bottom API 6B 26-3/4″ 5,000 psi
Side doors (left/right) – hinged entry
Nameplate – stainless steel with serial number and rating
Lifting eyes / lugs – heavy-duty ultra‑large handling
All parts are high-quality replacement – fully interchangeable with original Shenkai FZ68-35 components, meeting or exceeding OEM specifications.
Welcome to Hyrig – your trusted supplier for replacement Shenkai FZ76-7 ram blowout preventers (BOP) and all spare parts. The FZ76-7 features a nominal bore of 30 inches (762mm) with a 7MPa (1,000 psi) working pressure rating, making it suitable for diverter BOP applications in surface well control and shallow gas operations.
The model number FZ76-7 follows the Chinese industry standard:
FZ – Ram blowout preventer
76 – Nominal bore: 762mm (30 inches) ─ 76 represents the bore size in centimeters
7 – Maximum working pressure: 7MPa (1,000 psi)
Industry data confirms a direct equivalent FFZ76-07: 762mm (30″) bore, 7MPa (1,000 psi) working pressure, and 8.4 MPa - 10.5 MPa (1,200 - 1,500 psi) hydraulic control pressure.
Model: FZ76-7 (single ram configuration)
Nominal bore: 762 mm (30 inches)
Working pressure: 7 MPa (1,000 psi)
Strength test pressure: 10.5 MPa (1,500 psi)
Hydraulic control pressure: 8.4-10.5 MPa (1,200-1,500 psi)
Application: Diverter BOP systems, shallow well control at 30″ conductor stage
Hydraulic connection: NPT1″
Working medium: Oil, water, drilling fluid
Compliance: API Spec 16A
| Parameter | FFZ76-07 Value |
|---|---|
| Bore - mm (inches) | 762 (30) |
| Working pressure - MPa (psi) | 7 (1,000) |
| Control pressure - MPa (psi) | 8.4-10.5 (1,200-1,500) |
| Weight - kg (lb) | 13,866 (30,570) |
This reference BOP meets API Spec 16A compliance with a bolted cover design that enables efficient maintenance and side door access.
Ram rubber (packing element) – for 30″ bore; specify pipe sizes such as conductor pipe or surface casing
Front seal – ram front seal for 30″ BOP
Top seal – ram top seal
Side door seal – combined seal ring for 30″ side door interface
Complete seal kit (repair kit) – all O-rings, Y-rings, wipers, dynamic seals for full overhaul
Piston rod seals (Y-ring) – dynamic seal for hydraulic cylinder
Wiper rings / dust-proof rings
Ram block assembly (complete with rubber) – heavy-duty ultra‑large seating
Ram body – without rubber, for field rubber replacement
Ram shaft assembly
Piston rod – chrome-plated
Piston – for hydraulic cylinder
Hydraulic cylinder body
Cylinder head
Locking screw assembly – manual lock shaft, nut, handle
Leadscrew assembly
Stud bolts – for flanges and side door connections
Heavy hex nuts – corrosion-resistant grade
Ring gaskets – API flanged sealing up to 7MPa rating
Socket head cap screws, guide pins, retaining rings
BOP main body – single ram housing, cast alloy steel
Flanged connections – top and bottom, for 30″ nominal bore
Bolted cover – enabling convenient side door maintenance
Nameplate – stainless steel with serial number and rating
Lifting eyes / lugs – oversize lifting points for 30″ BOP handling
All parts are high-quality replacement – fully interchangeable with original Shenkai FZ76-7 and compatible 30″ ram BOP components, meeting or exceeding OEM specifications.
Stock availability – common wear parts for 26-3/4″ and 30″ BOPs ship within 7–14 days
Technical support – drawing verification before ordering; 26-3/4″ and 30″ flange, ring gasket, and ram selection support
International shipping – by air or sea to any oilfield, including offshore rigs with diverter BOP requirements
API compliance – manufactured to API Spec 16A
H2S resistant options – NACE MR0175 compliance for sour service on request for FZ68-35 surface BOP applications
26-3/4″ conductor and surface casing well control with 5,000 psi pressure rating
Offshore jackup surface BOP stacks – matched to 26-3/4″ 5,000 psi wellheads
Land deep drilling programs where large conductor casing diameters require 26-3/4″ BOPs at surface
30″ diverter BOP systems for offshore jackup and platform rigs
Shallow gas well control at the conductor casing stage where only 1,000 psi diverter capability is required
Diverter applications guided by API 16A diverter system regulations
Applications with 26-3/4″ diverter systems at 7MPa (1,000 psi) rating
The ultra-large bore ram BOPs are key components of surface well control stacks during early conductor casing intervals. For example, a 30″ diverter BOP with 7MPa rating is used at the conductor stage to divert shallow gas flow away from the rig, while a 26-3/4″ 35MPa (5,000 psi) ram BOP provides well barrier integrity for deeper conductor intervals.
Send your inquiry with:
Model number (FZ68-35 or FZ76-7)
Nominal bore (26-3/4″ or 30″)
Ram type and pipe size (pipe ram – casing size, blind ram, or shear ram)
Required rubber compound (standard or H2S-resistant)
Original part number (if available)
We will reply with a quote and technical drawing if needed.
For any inquiries, please contact us at info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.